메뉴 건너뛰기

ARC, Accelerating Rate Calorimeter

Thermal Safety Technology

Accelerating Rate Calorimeter

가속속도열량계 (단열가속열량계)

 

I. Equipment Purpose

본 장비는 시료의 온도 변화를 정밀하게 tracking함으로써, 시험 시료와 주변 환경 간의 열교환을 차단해 사실상 단열 상태의 환경(adiabatic environment)을 조성합니다. 주로 시험 시료의 발열 거동(exothermic behavior)을 측정하고 분석하는 데 사용됩니다. 가속속도열량계(ARC, accelerating rate calorimeter)를 활용하면 고에너지 케미컬이나 2차전지의 worst condition에 따른 발열반응, 자가발열속도(self-heat rate), 폭주온도(thermal runaway) 등의 열적 특성을 시뮬레이션할 수 있습니다. 이를 통해 실제 반응 과정에 더욱 근접한 환경을 구현하고, 열폭주 조건에서 나타나는 발열 반응의 속도론적 파라미터(kinetic parameter)를 도출할 수 있습니다.

당사의 열량계는 주로 대용량 배터리의 열폭주 특성을 시험하는 데 사용됩니다. 열폭주 특성 외에도, 사이클에 따른 발열 특성(cyclic heat generation)이나 비열 용량(Cp, Heat Capacity)과 같은 대용량 배터리의 다양한 열적 물성을 측정할 수 있습니다. 대표적인 제품으로는 ARC-D9, ARC-D20, ARC-D50, ARC-H60, ARC-L120, 등이 있습니다.

또한, 시험 대상 시료의 가스 방출(venting) 거동을 연구하도록 하는 '밀폐형 가속속도열량계(sealed accelerating rate calorimeter, sARC)'가 사용될 수 있습니다. Type II sARC의 경우, 가스 제어 시스템을 통해 밀폐된 정량(constant volume, CV) 용기 내부의 압력을 tracking하여, 열량계 내부의 압력을 동일하게 유지합니다. sARC는 기존 ARC의 기능을 그대로 유지하면서도, 배터리 열폭주 시 발생하는 가스 방출량 및 가스 방출 속도(gas releasing rate)와 같은 가스 방출 특성을 측정할 수 있습니다. 대표적인 제품으로는 sARC-D20s(Type I), sARC-D50s(Type I), sARC-D100s(Type II) 등이 있습니다.

(주)연진에스텍은 ARC의 판매와 서비스를 선도 수행한 20년의 노하우로, 용도에 따른 명확한 시스템의 구성이 가능하고, 안정성있는 시험과 측정기법, 데이터 해석의 제안, 신속한 A/S와 trouble shooting을 수행합니다. 

견적 문의: 02)501-7990, info@yeonjin.com 


II. Technical Specifications

Accelerating Rate Calorimeter Models

ARC-D9

ARC-D20

ARC-D50

ARC-L120

sARC-D20s

sARC-D50s

sARC-D100s

Temperature Range

RT-550℃

RT-350℃

RT-315℃

RT-315℃

Temperature Stability

±0.01°C/min

Temperature Resolution

0.001°C

Detection Sensitivity

0.02°C/min (calibration sensitivity ≥0.01°C/min)

Pressure Range

0-200 bar (open)

0-150 bar (open)

0-10/20/30 bar (sealed)

Pressure Detection Accuracy

≤0.05%

Operating Modes

Heating-Wait-Seek, Temperature Scanning, Isothermal, Specific Heat, GB36276 and other modes

Adiabatic Calorimetric Environment

Temperature difference between calorimetric chamber and sample ≤0.5°C (1°C for L120 and D100s), no false exothermic phenomenon

Adiabatic Tracking Capability

0.02-20°C/min

0.02-18°C/min

0.02-15°C/min

0.02-15°C/min

Effective Dimensions

Φ9×H10cm

Φ20×H25cm

Φ50×H50cm

L120×W50cm

Φ20×H25cm

Φ50×H50cm

Φ100×H120cm

Data Acquisition System

Supports Type N/K/B thermocouples, pressure sensors, battery voltage, and other signal inputs, with a maximum sampling rate of 100 Hz

Safety protection

Y

Y

Y

Y

Y

Y

Y

Charging Module

optional

2 built-in high-current binding posts with overcurrent capacity ≥600A

optional

2 built-in high-current binding posts with overcurrent capacity ≥600A

Needle Puncture Test Module

X

optional

optional

optional

optional

optional

optional

Specific Heat Capacity Test Module

optional

optional

optional

optional

optional

optional

optional

Low-Temper ature Test Module

optional

optional

optional

optional

optional

optional

optional

Multi-Point Temperature Field Distribution Test Module

optional

optional

optional

optional

optional

optional

optional

Gas Collection and External Pressure Test Module (Chamber-inChamber Solution)

optional

optional

optional

optional

X

X

X

Gas Collection System Module

optional

optional

optional

optional

optional

Y

Y

Atmosphere Simulation System

optional

optional

optional

optional

optional

Y

Y

Infrared Imaging System

X

optional

optional

optional

optional

optional

optional

Optical Imaging System

X

optional

optional

optional

optional

optional

optional

 

2. Parameters

2.1 Main Technical Parameters

  1. Thermocouples: 열량계는 N-type thermocouple을 채택하고 있으며, 이는 난연성(fire-retardant)을 갖추고 응답 지연이 적으며(anti-lag), 우수한 열전 안정성(thermoelectric stability)과 고온 산화 저항성(oxidation resistance)을 보입니다.
  2. Calibration: 열량계에는 교정(calibration ) 기능이 탑재되어 있는데, 이는 시료의 영향을 받지 않으며 매번 시험할 때마다 반복해서 교정할 필요가 없습니다. 또한, 교정 후에는 drift test를 수행하여 교정 파일의 온도 제어 안정성( temperature control stability)을 검증하고, 온도 드리프트(temperature drift )나 허위 발열 현상(false exothermic phenomen)이 발생하는지 확인해야 합니다.
  3. Safety protection: 본 장비에는 배터리의 열폭주(battery thermal runaway) 발생 시 자동으로 압력을 제거하도록 칼로리미터 챔버 본체를 보호하는 안전 압력 배출 장치(pressure relief device)가 구비되어 있습니다. 칼로리미터 챔버 본체는 실험실에 그대로 노출되어서는 안 되며, 외부에는 방폭함(explosion-proof box)을 설치하여 챔버와 오퍼레이터를 분리해야 합니다. 즉, 잠재적인 챔버 폭발 및 고속 가스 분출로부터 오퍼레이터의 안전을 보장해야 한다.

 

2.2 Main Technical Requirements for Each Sub-system

2.2.1 Main Unit of Accelerating Rate Calorimeter

  1. Equipped with a large-volume calorimeter for large-size power battery testing, tests shall be completed in an explosion-proof box, and equipped with emergency cooling and high-power exhaust systems;
  2. The entire calorimeter system shall operate inside the explosion-proof box;
  3. The explosion-proof box is equipped with an automatic air blower, fully controlled by computer;
  4. The exhaust equipment can be connected to the laboratory's exhaust system;
  5. The explosion-proof box is equipped with safety interlock devices controlled by both hardware and software;
  6. The explosion-proof box minimizes the potential risk of gas escaping into the laboratory;
  7. The system can integrate other calorimeters without adding additional circuits, software or other components;
  8. The calorimeter control system can control two or more adiabatic calorimeters with a single set of control system.

 

2.2.2 Calorimeter Structural Design

  1. The calorimeter is made of aluminum with good thermal conductivity, and all inner walls (top, side and bottom) are 20mm thick to ensure sufficient thermal stability;
  2. The calorimeter is equipped with eight heaters, three independent adiabatic control zones, and three independent temperature-control sensors;
  3. The calorimeter chamber incorporates thermal insulation to minimize heat exchange with the external environment;
  4. The calorimeter has explosion-proof and pressure relief design, and adopts magnetic sealing to facilitate automatic pressure relief during battery thermal runaway and protect the calorimetric chamber body.

 

2.2.3 Battery Nail Penetration Module

  1. Mounted on the side of the calorimeter and directly connected to the inside of the calorimeter;
  2. Nail Penetration Stroke: 100mm, default;
  3. Needle diameter: 3mm;
  4. Number of needles: 10;
  5. Speed range: 1mm/sec to 100mm/sec;
  6. Maximum needle force: 675N;
  7. Fully automatic control and data collection.

 

2.2.4 Single-Channel Gas Collection System Module

  1. Built-in control software;
  2. Built-in supporting circuit;
  3. Gas cylinder with volume 300/500/1000mL and built-in control valve;
  4. Automatically controlled ball valve switch; 5. Auxiliary gas pipelines, joints and fixing frames.

 

2.2.5 Software Unit

  1. Equipment operation and control software;
  2. Relevant software required for the workstation;
  3. Data analysis software;
  4. Lifetime free software upgrades for the instrument.

 

2.2.6 Compliance with Relevant Test Standards

  1. USABC SAND99-0497, July 1999: 3.2 Thermal Stability Tests
  2. SAE J2464-R2009: 4.4.2 Thermal Stability Tests
  3. FreedomCAR SAND 2005-3123: 4.1 Thermal Stability
  4. ASTM E1981-98(2004)
  5. SN/T3078.1-2012 Guidelines for the Evaluation of Thermal Stability of Chemicals - Part 1:Accelerating Rate Calorimeter Method
  6. GB/T-36276 (2023)

 

2.2.7 Workstation Requirements

  1. Brand: Well-known brand;
  2. CPU: No less than Intel® Xeon® Processor E5-1630 v3 (4C HT, 10MB Cache, 3.7GHz Turbo);
  3. Memory: 16GB (4×4GB) 2400MHz DDR4 RDIMM ECC;
  4. Hard Disk: 500GB 3.5-inch SATA (7,200 Rpm);
  5. Operating System: Windows 11;
  6. Specialized Software: ARC system operation software, ARC data analysis and image processing software.

 

2.2.8 Other Requirements

  1. The system shall reserve upgrade space for battery testing applications;
  2. Provide 12-month warranty, and lifelong supply of instrument spare parts, technical support and after-sales service.