메뉴 건너뛰기

Application

유전율측정기

Equipment for Dielectric Cure Monitoring

연진에스텍 2020-03-31 14:25:52 923

Dielectric cure monitor는 단일 주파수 또는 다양한 주파수 영역에서 유전체의 전기적 특성을 측정하며, mobile Ion 및 dipole rotation의 영향을 선택적으로 나타냅니다. 본 유전율 분석 시스템으로 측정하여 축적된 데이터를 기반으로 사용자는 첨단 소재를 사용한 연구개발, 제조 및 품질 관리 프로세스 단계를 신뢰성 있게 진행하고 정보에 입각한 결정을 내릴 수 있습니다.

아래 그림은 본 경화거동 분석기의 필수 요소를 나타냅니다. 열경화성 재료 테스트에 있어 유전/전도 센서는 평행판 또는 깍지형 전극판의 두 가지 일반적인 구성을 갖습니다. 센서의 선택은 원하는 측정 유형(표면 또는 부피)과 A/D 비율에 따라 달라집니다. 센서는 계측기에 연결되며, AC 신호를 사용하여 복합적인 경화거동 분석을 수행합니다. 폭넓은 대역의 여기 주파수는 최적의 ion viscosity를 관찰할 수 있으며, 다중 주파수는 극성 반응을 연구할 수 있도록 합니다. 온도 측정은 경화를 이해하는데 중요하며, 특히 비등온 조건에서 중요합니다.

마지막으로, 소프트웨어는 본 분석기에 연결된 컴퓨터를 통해 계측기를 제어합니다. 단일 지점 측정에는 열경화성 재료나 복합 경화제의 상태를 확인할 수 없고 시간이 흐름에 따른 ion viscosity의 변화나 곡선의 모양에서 상태를 추출해야 합니다. 따라서 반복적인 측정, 데이터의 분석과 저장을 하는 소프트웨어는 시스템에 매우 중요합니다.

 

Essential elements of dielectric cure monitoring system

 

Dielectric cure monitors measure the dielectric properties of material at a single frequency or across a range of frequencies, selectively revealing the influence of mobile ions and dipole rotation. Armed with the data this equipment reveals, users of dielectric cure monitors can make well-informed decisions as they work with advanced materials, moving through the stages of R&D, manufacturing, and quality control processes with confidence and improved efficiencies.  

The figure below shows the essential elements of a dielectric cure monitoring system. Making contact with the thermoset under test, dielectric/conductivity sensors have two general configurations, parallel plate or interdigitated electrodes. The selection of a sensor depends on the desired type of measurement, either surface or bulk, and the desired sensitivity as indicated by the A/D ratio.

Sensors connect to an instrument, and the most versatile instruments use AC signals for composite cure monitoring. A wide range of excitation frequencies allow selection of an optimal frequency for observing ion viscosity, and multiple frequencies enable studies of the dipolar response. Temperature measurement is important for understanding cure, especially under non-isothermal conditions.

Finally, software controls the instrument, usually through a computer connected to the dielectric cure monitor. Thermoset or composite cure state cannot be determined from a single point measurement, but must be extracted from the change of ion viscosity and the shape of the curve over time. So software, which makes repetitive measurements, and stores and analyzes data, is crucial to the performance of the system.

 

Reference :

Lambient TechnologiesTM Technical Overview 3.05—Equipment for Dielectric Cure Monitoring, Page  7

 

상세한 사항은 아래 첨부된 자료를 참고 부탁 드립니다.